6.1 General

6.1.1 Topics

This clause addresses conformance of X3D files, X3D generators and X3D browsers.

The topics covered in this clause are shown in Table 6.1.

6.1.2 Objectives

The primary objectives of the specifications in this clause are:

1. to promote interoperability by eliminating arbitrary subsets of, or extensions to, ISO/IEC 19775;
2. to promote uniformity in the development of conformance tests;
3. to promote consistent results across X3D browsers;
4. to facilitate automated test generation.

6.1.3 Scope

Conformance is defined for X3D files and for X3D browsers. For X3D generators, conformance guidelines are presented for enhancing the likelihood of successful interoperability.

A concept of base profile conformance is defined to ensure interoperability of X3D generators and X3D browsers. Base profile conformance is based on a set of limits and minimal requirements. Base profile conformance is intended to provide a functional level of reasonable utility for X3D generators while limiting the complexity and resource requirements of X3D browsers. Base profile conformance may not be adequate for all uses of X3D.

This clause addresses the X3D data stream and implementation requirements. Implementation requirements include the latitude allowed for X3D generators and X3D browsers. This clause does not directly address the environmental, performance, or resource requirements of the generator or X3D browser.

This clause does not define the application requirements or dictate application functional content within a X3D file.

The scope of this clause is limited to rules for the open interchange of X3D content.

6.2 Conformance

6.2.1 Conformance of X3D files

An X3D file is syntactically correct according to this document if the following conditions are met:

1. The X3D file contains as its first element an X3D header statement (see 7.2.5.2 Header statement) specifying the version to which this file conforms. Versions and associated content are specified in AnnexZVersion content.
2. All entities contained therein match the functional specification of entities of this document that correspond to the version specified in the header statement. The X3D file shall obey the relationships defined in the formal grammar and all other syntactic requirements.
3. The sequence of entities in the X3D file obeys the relationships specified in this document for the version specified in the header statement producing the structure specified in the part of ISO/IEC 19775 for the version specified in the header statement.
4. All field values in the X3D file obey the relationships specified in this document for the version specified in the header statement producing the structure specified in this document for the version specified in the header statement.
5. No nodes appear in the X3D file other than those specified for the applicable profile as specified in this document unless specified in a COMPONENT statement, are required for the encoding technique, or are those defined by the PROTO or EXTERNPROTO entities should such be available in the profile.
6. No nodes or fields appear in the X3D file other than those defined as part of the version specified in the header statement.
7. The X3D file is encoded according to the rules of ISO/IEC 19776.
8. It does not contain behaviour described as undefined in this document.

6.2.2 Conformance of X3D generators

A X3D generator is conforming to ISO/IEC 19775 if all X3D files that are generated are syntactically correct and meet the requirements state in 6.2.1 Conformance of X3D files.

A X3D generator conforms to a profile if it can be configured such that all X3D files generated conform to that profile.

6.2.3 Conformance of X3D browsers

An X3D browser is conforming if:

1. It is able to read any X3D file that conforms to the profiles and components supported by that X3D browser for the version(s) and encoding(s) supported by that browser.
2. It implements the functionality specified for all abstract interfaces, insofar as they are made available in concrete nodes derived from those interfaces, within the latitude defined for the specified profile, components, and version and as allowed in this clause.
3. It presents the graphical and audio characteristics of the X3D nodes in any X3D file that conforms to the applicable profile, components, and version, within the latitude defined for the specified profile, components, and version and as allowed in this clause.
4. It correctly handles user interaction and generation of events as specified for the applicable profile, components, and version, within the latitude defined for the specified profile, components, and version and as allowed in this clause.
5. It satisfies the minimum support requirements for X3D browsers for the applicable profile as enumerated in the table of minimum support requirements for that profile.

6.3 Minimum support requirements

6.3.1 Minimum support requirements for generators

There is no minimum complexity which is required of (or appropriate for) X3D generators. Any compliant set of nodes of arbitrary complexity may be generated, as appropriate to represent application content, and which produce only the nodes allowed by the applicable profile, components, and version.

6.3.2 Minimum support requirements for X3D browsers

Each profile defines the minimum complexity which shall be supported by an X3D browser in support of that profile. X3D browser implementations may choose to support greater limits but may not reduce the limits described for the applicable profile. When the X3D file contains nodes which exceed the limits implemented by the X3D browser, the results are undefined. The words "optionally supported" in the minimum browser support column refers only to the display of the item; in particular, set_ events to ignored inputOutput fields shall still generate corresponding _changed events. Where latitude is specified in a table of minimum support requirements for a particular node, full support is required for other aspects of that node.